Price a maintenance visit the same way you'd price any service call: technician time at your loaded hourly rate, plus consumables (filters, refrigerant top-off if included, coil cleaner), plus drive time. Add a margin on top, then package the whole thing into a seasonal or annual agreement with a clearly stated task list so the customer knows exactly what's covered and what triggers a separate repair estimate.
That packaging step is where most shops either make good money or quietly lose it. A one-off tune-up priced at cost plus a little margin feels fine in isolation. But maintenance work is where you build recurring revenue, and recurring revenue only works if the price covers your real cost to deliver it twice a year, every year, without you re-deriving the number each time.
{"h2": "Start With Technician Time, Not a Guess"}
Time the actual visit, not the advertised visit. A single-system tune-up — clean the coil, check refrigerant charge, inspect the condensate line, check electrical connections, swap or inspect the filter, test capacitors and contactors — typically runs 45 to 75 minutes for a tech who knows the equipment. If your techs are newer or the system is old and finicky, budget closer to 90 minutes.
Multiply that time by your fully loaded hourly rate, not just wages. Loaded rate means wages plus payroll taxes, insurance, vehicle cost, and a share of overhead — most shops land somewhere between $55 and $95 per billable hour once that's all folded in. If you haven't calculated your own loaded rate, this breakdown of labor, materials, overhead, and profit walks through the math.
{"h2": "Add Consumables and Drive Time"}
Consumables for a basic tune-up are cheap but they add up across a route: a standard filter runs $5 to $25 depending on size and MERV rating, coil cleaner and condensate tablets are a few dollars per visit, and if your agreement includes minor refrigerant top-off, build in an allowance rather than eating it. If a system needs more than a pound or two of refrigerant, that's a diagnostic finding, not a maintenance task — quote it separately.
Drive time matters more for maintenance than for repair work because you're often running a tight route of six or eight stops in a day. Use your actual average drive time per stop, not zero. If you serve a 20-mile radius, 15 to 20 minutes between stops is realistic once you include parking and walking to the unit. For a deeper look at building this into every estimate, see how to estimate travel time and fuel costs for service jobs.
{"h2": "Package It Into an Agreement With a Stated Task List"}
Once you know your true cost per visit, build the customer-facing price around a plan, not a single visit. Two visits per year — spring cooling check, fall heating check — is the standard structure for most residential HVAC agreements. Price the plan at your per-visit cost times two, plus margin, then present it as one annual number or a monthly auto-pay amount so it reads as a subscription rather than two separate bills.
Publish the task list on the agreement itself. Customers who can see exactly what's included stop calling to ask why a repair wasn't free, and your techs have a checklist that keeps every visit consistent regardless of who's on the truck that day. A typical published list for a cooling visit:
{"ul": ["Inspect and clean or replace air filter","Check refrigerant charge and pressures","Clean condenser coil exterior","Flush and treat condensate drain line","Test capacitors, contactors, and relays","Check thermostat calibration and operation","Inspect electrical connections and tighten as needed","Lubricate moving parts where applicable","Verify safety controls and airflow"]}
A heating visit swaps in burner or heat strip inspection, ignition system check, heat exchanger inspection on gas furnaces, and carbon monoxide testing in place of the cooling-specific items.
{"h2": "Per-System Pricing for Multi-Unit Homes"}
Larger homes with two or three zones need per-system pricing, not a flat per-visit rate. The first system carries most of your fixed cost — the drive to the property, setup, paperwork — so it's reasonable to price it at full rate. Each additional system on the same visit costs you less incremental time, typically 30 to 45 minutes instead of a full visit, so price it at 50-65% of the first system's rate rather than charging full price twice.
A common structure: $139-$189 for the first system's seasonal visit, $79-$109 for each additional system on the same visit. For a three-system home on a two-visit annual plan, that lands around $600-$800 per year depending on your market and loaded rate. Adjust these anchors to your own cost numbers — they're a starting structure, not a price you should copy without checking your own labor rate against them.
Commercial rooftop units and packaged systems are a different animal entirely and usually get quoted per unit with a site-specific scope, since access, unit age, and filter sizing vary too much for a standard residential rate to hold.
{"h2": "What to Exclude From the Maintenance Price"}
The agreement price has to stop somewhere or you'll eat repair costs under the maintenance umbrella. Spell out the boundary in writing:
{"ul": ["Refrigerant beyond a stated small allowance (e.g., 1 lb)","Part replacement — capacitors, contactors, motors, igniters found worn or failing","Duct cleaning or duct repair","Coil replacement or deep chemical coil cleaning","Electrical panel or wiring repairs beyond tightening connections","Thermostat replacement (inspection and calibration only is included)"]}
When a tech finds something during the visit that falls outside this list, that's a diagnostic finding, not scope creep. Write it up as a separate estimate on the spot — most maintenance plan customers expect this and it's often the best lead source you have, since you're already standing in front of the equipment. How to estimate a plumbing repair before opening a wall covers the same logic for the trade next door: price what you can see, flag what you can't, and don't fold unknowns into a flat rate.
{"h2": "Keep the Price Book and Agreements Consistent"}
Maintenance pricing only stays profitable if every tech quotes the same add-on repairs the same way and every agreement gets built from the same base numbers. A price book solves that — your per-system rates, consumables, and common add-on repairs live in one place instead of in each tech's head. Trusso's AI estimate tool builds quotes anchored to your own price book, which keeps a filter swap or a capacitor replacement priced the same whether it's job one of the day or job eight. The HVAC trade page covers how that fits with scheduling recurring maintenance visits and tracking which systems are due. If you're evaluating software generally, this roundup of estimating apps for HVAC contractors is a useful starting point for comparing options beyond just Trusso.
How much should an HVAC maintenance visit cost?
Most single-system residential tune-ups run $100-$200 per visit depending on labor rate, market, and what's included. A two-visit annual agreement typically lands at $180-$350 per year for one system once you price in both the spring and fall visit plus a margin.
Should refrigerant be included in a maintenance plan price?
Include a small allowance, such as up to one pound, and quote anything beyond that as a separate repair. Refrigerant needs beyond a minor top-off usually point to a leak, which is a diagnostic and repair job, not routine maintenance.
How do you price maintenance for a home with multiple HVAC systems?
Charge full rate for the first system, since it carries the drive time and setup cost, then discount each additional system on the same visit to roughly 50-65% of the first system's rate since the incremental time is lower.
Should maintenance agreements be billed annually or monthly?
Either works as long as the total matches your per-visit math times the number of visits plus margin. Monthly auto-pay tends to improve plan retention and feels more affordable to the customer, even though the annual total is the same.
What should be excluded from a flat maintenance price?
Part replacement, duct work, coil replacement, and refrigerant beyond a small stated allowance should always be quoted separately. Publishing this exclusion list on the agreement prevents disputes when a tech finds a failing part during the visit.
Run your business the simple way
Try Trusso free for 14 days and send your first estimate in minutes.
Start 14-Day Free TrialKeep reading
What Is Construction Takeoff Software and Do Small Contractors Need It?
Takeoff software measures quantities—areas, lengths, counts—straight from plans so you can price a job without a tape measure and a calculator. Here's when a small contractor actually needs it.
Read articleComparisons7 Best Contractor Foreman Alternatives for General Contractors
Contractor Foreman covers a lot of ground but little of it goes deep. Here are 7 alternatives GCs switch to once they need real takeoff, sub bid-outs, or sharper scheduling.
Read article