The Direct Answer
Estimate a fence job by multiplying linear footage by a per-foot rate for your chosen material and height, then adding line items for gates, corner/end posts, difficult digging (rock, roots, slope), old fence demo and haul-off, and any permit or survey requirement. Linear-foot pricing covers the straight runs; everything else is extra and needs to be priced separately or the job loses money.
Fence estimating trips up a lot of contractors because the quote looks simple on paper — "it's just posts and panels" — but the real cost swings depend on things you can't see from the street. A 150-foot run on flat, soft soil with no gates is a different job than 150 feet with two corners, a double-wide gate, and three feet of elevation change. Treat linear footage as your starting number, not your final one.
Before anything else, walk the line. Note where the fence turns (each corner needs a stronger post), where gates go, what's underground (call 811 first), and what the current condition of the yard looks like. If you're pricing from photos a customer sent instead of a site visit, read how to estimate a job when you cannot see the property in person before you quote — terrain and soil are exactly the kind of detail that gets missed remotely.
Price Per Linear Foot by Material and Height
Material and height drive the base number more than anything else. These are typical installed ranges (materials plus labor) for a standard residential run — your local lumber and labor costs will shift these up or down:
| Material | Height | Typical installed cost per linear foot |
|---|---|---|
| Pressure-treated wood (dog-ear or board-on-board) | 6 ft | $25–$40 |
| Cedar privacy | 6 ft | $30–$50 |
| Chain link, galvanized | 4 ft | $12–$22 |
| Vinyl privacy | 6 ft | $30–$55 |
| Aluminum/steel ornamental | 4–5 ft | $35–$60 |
| Split rail or ranch rail | 3–4 ft | $18–$28 |
Taller fences cost more per foot, not just more in total — a 6-ft wood fence isn't simply 1.5x the cost of a 4-ft version because post depth, panel weight, and bracing all increase too. If you quote a range instead of a flat number on a borderline job, make sure the customer understands why — see how to explain an estimate range without making a firm promise.
What Isn't Covered by the Per-Foot Rate
- Posts and corners — End posts, corner posts, and gate posts are bigger, set deeper, and often need concrete footings. Price these as a per-post add-on ($40–$120 each depending on material and depth), not inside the linear-foot number.
- Gates — A single walk gate with hardware typically adds $150–$400; a double drive gate with a drop rod or automatic opener can run $600–$1,500+. Gates also take more labor time per foot than straight fence line.
- Terrain and digging conditions — Rocky soil, tree roots, or a slope that requires stepped or racked panels all slow down digging and installation. If you hit rock on even one test hole, build in a per-post surcharge or a contingency line rather than eating the overage.
- Demo and haul-off of the old fence — Pulling posts set in concrete is slower than pulling ones set in dirt. Price demo separately, usually $3–$8 per linear foot depending on material and disposal distance.
- Permits and surveys — Many municipalities require a permit for fences over a certain height, and HOAs sometimes require the property line to be confirmed. If the customer doesn't have a recent survey and the fence sits near a boundary, flag it before you dig — a misplaced fence is an expensive mistake to undo.
A Worked Example: 150 Linear Feet of Wood Privacy Fence
Here's how the pieces stack for a realistic residential job:
- 150 linear feet of 6-ft cedar privacy fence at $38/ft = $5,700
- 2 corner posts at $90 each = $180
- 1 gate post pair + 4-ft walk gate with hardware = $320
- Terrain surcharge for 20 ft of sloped, rocky section at $6/ft extra = $120
- Demo and haul-off of old 120 ft wood fence (dirt-set posts) at $4/ft = $480
- Permit fee (flat, pulled by contractor) = $75
Subtotal: $6,875. Add your material waste factor — fence panels and pickets don't cut evenly across odd run lengths, so most contractors build in 8–10% extra material on top of the straight linear-foot count. If you're not already building waste into every estimate, this breakdown of material waste factors walks through how to calculate it by material type instead of guessing. On this job, 8% waste on the materials portion (roughly $3,400 of the $5,700 is material) adds about $270, bringing the total to around $7,145 before overhead and profit markup.
Don't forget to layer in your overhead — fuel, insurance, tool wear, and admin time — before you apply margin. This guide to overhead costs covers what belongs in that number so you're not pricing off labor and materials alone.
Keep the Line Items Separate on the Quote
Resist the urge to blend everything into one lump linear-foot price. If a customer sees "150 ft fence — $7,145" with no breakdown, any question about cost turns into a negotiation over the whole number. If they see linear footage, posts, gate, terrain, demo, and permit as separate lines, you can discuss or adjust one piece — say, skipping demo because they'll pull the old fence themselves — without re-pricing the entire job. It also makes it obvious, if the crew hits unexpected rock mid-dig, which line item the change order applies to.
If you want a fast starting number before you build the full line-item quote, the free AI fence estimate generator will rough out material, height, and length pricing in a minute so you're not doing the per-foot math by hand on every call.
How Trusso Fits In
Once you've got your price book dialed in for wood, vinyl, chain link, and ornamental fence by linear foot, Trusso lets you turn a site visit into an itemized estimate — posts, gates, demo, and permit fees as separate lines — in a few taps, anchored to your own published prices so the number stays consistent job to job. It's part of the same flat-rate plan that also handles scheduling, crew assignments, and invoicing, starting at $29/month for an owner plus two crew, with no per-user fees and a 14-day free trial.
How many linear feet of fence do I need for a typical backyard?
A standard quarter-acre suburban lot runs anywhere from 150 to 250 linear feet of fence depending on lot shape and whether the front yard is included. Always measure the actual property rather than estimating from lot size — irregular lots and existing structures change the number significantly.
Should I price fence gates by the linear foot or as a flat add-on?
Price gates as a flat add-on, not by linear foot. Gates require extra hardware, stronger posts, and more labor time per foot than straight fence line, so folding them into your per-foot rate either undercharges the gate or overcharges the rest of the run.
How much extra should I charge for rocky or sloped terrain?
Many contractors add a per-post or per-linear-foot surcharge (commonly $5–$10 extra per foot) for sections with rock, heavy roots, or significant slope that requires stepped panels. If you can't assess the terrain before digging, note it as a contingency line on the estimate rather than guessing a flat number.
Do I need a permit to install a residential fence?
It depends on your municipality and the fence height — many areas require a permit for fences over 6 feet or fences near a property line, while lower fences in the backyard often don't need one. Check local rules before quoting, and build the permit fee into the estimate as its own line if one is required.
What's a fair markup for demo and haul-off of an old fence?
Demo pricing usually runs $3–$8 per linear foot depending on whether posts are set in dirt or concrete and how far you have to haul debris. Concrete-set posts take noticeably longer to pull, so price those sections higher than a fence that's simply nailed or screwed together.
Run your business the simple way
Try Trusso free for 14 days and send your first estimate in minutes.
Start 14-Day Free TrialKeep reading
What Is Construction Takeoff Software and Do Small Contractors Need It?
Takeoff software measures quantities—areas, lengths, counts—straight from plans so you can price a job without a tape measure and a calculator. Here's when a small contractor actually needs it.
Read articleComparisons7 Best Contractor Foreman Alternatives for General Contractors
Contractor Foreman covers a lot of ground but little of it goes deep. Here are 7 alternatives GCs switch to once they need real takeoff, sub bid-outs, or sharper scheduling.
Read article