Trusso logoTrusso
All articlesEstimating

How Do You Price Fence Repairs When the Full Scope Is Unknown?

The Trusso TeamNovember 20, 20268 min read

Price the visible repair firm, then set a per-post and per-section rate for whatever you find once you start pulling boards and digging around posts. Cap the whole thing with a not-to-exceed number the customer approves up front. That gives you a real price to sell against, protects you from eating rot you couldn't see, and keeps the customer from feeling blindsided when the invoice shows up.

Fence repair is one of the worst jobs to quote flat-rate from a driveway walk-through. A leaning section might be one bad post or it might be four posts rotted below grade with a buried concrete footing nobody mentioned. You won't know until you dig, and digging is part of the job you're being asked to price before you've done it.

The fix isn't to guess bigger and pad the number until you feel safe. That makes you lose jobs to contractors who quote tighter, even if their price turns into a mess later. The fix is to separate what you can see from what you can't, price each piece the way it actually behaves, and put a ceiling on it so the customer knows their worst case before they sign.

Start with what you can actually see and measure

Walk the fence and write down every visible problem: leaning posts, split or missing pickets, sagging rails, gates that won't latch, sections pushed by a tree root or a storm. Count linear feet of fence that's visibly affected and count individual components — posts, rails, pickets, gate hardware — separately. This is the part of the estimate you can price firm, the same way you'd price a straight fence installation: material cost, labor hours, your markup, done.

Firm pricing on the visible scope matters because it's the number the customer anchors to. If every line item on your estimate is a range or a "TBD," you look unsure of your own trade. Give them certainty on what you know and flag uncertainty only where it's real — underground and inside the structure.

Set a per-post rate before you dig, not after

The biggest unknown in fence repair is almost always what's happening below grade. A post that looks fine at the surface can be rotted the last 12 inches, snapped off in the concrete, or sitting in a footing that's heaved and cracked. You can't price that from a walk-through, so don't pretend to. Instead, quote a flat per-post replacement rate that already accounts for digging, removing the old post and footing, setting a new post, and patching the concrete.

A realistic structure looks like this:

  • Visible repair (named posts, rails, pickets): firm price
  • Each additional post found rotted or broken below grade: flat rate per post (covers demo, haul-off, new post, concrete, labor)
  • Each section of rail or picket run that has to come out to access a bad post: flat rate per linear foot
  • Old concrete footing removal, if it's oversized, double-poured, or has to be jackhammered: separate flat add

Quoting a flat per-post rate instead of time-and-materials on the unknowns does two things. It lets the customer do rough math on their own worst case, and it protects your margin if a post turns out to be an easy pull instead of a fight with an old concrete footing — you don't have to justify your hours line by line.

Concrete removal is where repair estimates blow up

Old fence concrete is unpredictable in a way wood rot isn't. Some footings are a thin 6-inch sleeve you can pop out with a bar in two minutes. Others are 18 inches deep, poured wider than code requires, or tied into a neighbor's footing from a shared post. You genuinely cannot know which one you're dealing with until the post is cut off and you're standing over the hole.

Build this into your per-post add-on as a tiered price instead of one flat number: a base rate that assumes a normal footing, and a clearly stated upcharge if the footing takes more than a set amount of time to break out — say, anything past 20 minutes of jackhammering becomes a per-15-minute add. Put that threshold in writing on the estimate so there's no argument about when the upcharge kicks in.

Put a ceiling on it — the not-to-exceed number

This is the piece that makes the whole approach work for the customer, not just for you. Take your firm visible-repair price, estimate the worst realistic case for the unknowns (every post along the affected run needs replacing, the footings are all bad), and give the customer a not-to-exceed total. Tell them plainly: "Your price is between $X and $Y. I won't charge past $Y without calling you first and showing you what I found."

That one sentence does more to win the job and avoid disputes than any amount of itemizing. Customers aren't afraid of variable pricing — they're afraid of open-ended pricing. A capped range reads as honest. An estimate that says "TBD" or "price may change" with no ceiling reads as a blank check, and plenty of homeowners have been burned by exactly that before. If you want more language for handling this conversation, see how to tell a customer their final price may change.

If you hit the ceiling and there's still more wrong than anyone expected — an entire run of posts rotted, not just three — that's not a change order anymore, that's a conversation about stopping and re-scoping. Don't quietly blow through your own cap; call the customer, show them photos of what you found, and get a new number approved before continuing. Documenting extra work before asking for approval applies just as much here as it does on any other trade.

When repair stops making sense versus replacement

There's a point on every fence repair job where you should stop pricing patches and start recommending replacement instead. Rough thresholds that hold up in practice:

  • More than 30–40% of the posts along a run need replacing
  • The fence is older than its expected material lifespan (roughly 15–20 years for untreated wood, longer for vinyl or PT lumber) and you're finding rot in posts you weren't even called out for
  • The customer's per-post repair total, once you add it up, lands within 60–70% of what a full new section would cost
  • Rails and pickets are brittle or warped enough that reusing them after disturbing the structure risks more breakage than the repair is worth

When you hit one of these, say so directly. "I can patch these three posts, but at this price, and given the age of the rest of the fence, you're one storm away from calling me back for the next section. A full rebuild of this run would cost about this much and come with a warranty on the whole thing." Customers respect that more than a contractor who quietly repairs forever and never mentions the fence is dying.

Get the visible scope priced fast, then quote the unknowns with structure

You still need a fast, accurate starting number for the part of the job you can see before you build out the per-post and per-footing add-ons. The free AI fence estimate generator will turn a description or photos of the damaged sections into a baseline labor and material estimate in a couple of minutes, which you can then layer your contingency pricing on top of.

If you're running these jobs out of Trusso, you can build the per-post and per-footing rates into your price book once and pull them into every repair estimate instead of recalculating from scratch each time, then attach the not-to-exceed language and photos directly to the estimate the customer approves. Trusso runs flat at $29, $59, or $99 a month depending on crew size, with no per-user fees and a 14-day free trial.

Should I charge for the diagnostic time of digging up a post before I know the real scope?

Yes, or build it into your per-post rate. Digging out one post to assess footing condition takes real labor whether or not that post ends up needing replacement. Many contractors fold a small diagnostic allowance into the first post's rate and charge the flat per-post price for every one after that.

What if the customer refuses a not-to-exceed and wants a single flat price instead?

You can give one, but price it at the high end of your realistic worst case, not the middle. Be upfront that a single flat number on unopened structure means you're pricing in your risk, and it will likely come in higher than the range approach would average out to.

How do I handle a fence repair where the property line or ownership of the fence is unclear?

Get that settled before you price anything, not after. If a shared fence with a neighbor is involved, note on the estimate that the price assumes your customer is authorizing and paying for the full repair, and recommend they confirm cost-sharing with the neighbor separately.

Is it worth itemizing the concrete removal upcharge, or should I just build a buffer into the per-post rate?

Itemize it. A buffer hides your logic and invites argument if a customer feels like you're overcharging for an easy post. A stated threshold — a base rate plus a per-15-minute add past a certain point — is easy to defend because you can point to exactly why the charge applied.

Do I need a change order if a repair job goes from 3 posts to 6 but stays under my not-to-exceed?

Not strictly, since the customer already approved that range, but send a quick update anyway — a photo and a one-line note that you found 3 more bad posts and the total is landing at $X. It keeps trust intact even when you're technically within what they signed off on.

Run your business the simple way

Try Trusso free for 14 days and send your first estimate in minutes.

Start 14-Day Free Trial